ASTM F2413 05 PDF

1 | Page. ASTM. American Society For Testing and Materials. F Standard Specification for Performance Requirements for Foot. Protection. Abstract. Learn about ASTM footwear standards and how to properly read a label. The 11 after the dash signifies the footwear meets the ASTM F or F ASTM F EH Overshoes are made from yellow ozone resistant rubber that’s % waterproof.

Author: Grokus Faezuru
Country: Reunion
Language: English (Spanish)
Genre: Health and Food
Published (Last): 14 August 2005
Pages: 432
PDF File Size: 16.28 Mb
ePub File Size: 10.35 Mb
ISBN: 221-4-22342-931-4
Downloads: 95271
Price: Free* [*Free Regsitration Required]
Uploader: Tygojora

The values given in parentheses are for information only. This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to be worn to provide protection against a variety of workplace hazards that can potentially result in injury.

Historical Version s – view previous versions of standard. These references can be found in Cancel reply Enter your comment here Static dissipative SD footwear is designed to reduce the accumulation of excess static electricity by conducting body charge to ground while maintaining a sufficiently high level of resistance.

It also identifies the existence of impact resistance Ithe impact resistance rating 75, 50 or 30 foot-poundscompression resistance Cand the compression resistance rating 75, 50, or 30, which correlate to pounds, pounds, and pounds of compression respectively.

OSHA & ASTM Protective Footwear Requirements – EHS Safety News America

Footwear conforming to this specification must meet the performance requirements for the following: All footwear manufactured to the ASTM specification must be marked with the specific portion of the standard with which it complies.

Conductive Cd footwear is intended to protect the wearer in an environment where the accumulation of static electricity on the body is a hazard. The footwear must have a lower limit of electrical resistance of ohms and an upper limit of ohms. Accept all cookies or Manage cookie settings.

Most manufacturers of asrm devices have submitted their products to independent laboratories for testing. The existence of metatarsal resistance Mt and the rating 75, 50 or 30 foot-pounds is identified. Effective with the last revision of this standard, the ANSI Z requires suppliers and manufactures of Protective Footwear to have independent laboratory test results available to confirm 2f413 with the standard.

  LA EVOLUCION DE MEXICO ANGEL MIRANDA BASURTO PDF

The metatarsal designation Mt and rating 75 or 50 foot-pounds is also identified. Published by Jack Benton.

These ast used to designate conductive Cd properties, electrical hazard resistance properties EHfootwear designed to reduce the accumulation of excess static electricity SDand puncture resistance PR. Electrical hazard EH footwear is manufactured with non-conductive, electrical shock-resistant soles and heels. The electrical resistance must range between zero andohms.

Protective footwear can meet all the requirements of the ANSI standard or specific elements of it, as long as it first meets the requirements for toe protection in Section 1. Per Appendix B to Subpart I safety shoes or boots with impact protection are suggested for carrying or handling materials such as packages, objects, parts or heavy tools, which could be sstm and, for other activities where objects might fall onto the feet.

Conductive Cd footwear is intended to provide protection for the wearer against hazards resulting from static electricity build-up and to reduce the possibility of igniting explosives and volatile chemicals.

It is intended to provide a secondary source of protection against accidental contact with live electrical circuits, electrically energized conductors, parts or apparatus.

ASTM F – 05 Standard Specification for Performance Requirements for Foot Protection

The revision f24133 the references in these regulations to recognize the more recent editions of the applicable national consensus standards. Line four is to be used when more than three sections of the standard applies to the footwear. I’m a client Email. Sorry, your blog cannot share posts by email.

The puncture resistant footwear must show no signs of cracking after being subjected to 1.

It is designed to dissipate state electricity from the body to the ground. The marking must be enclosed in a rectangular border; a four-line format is recommended.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The final rule went into effect in October This data and its results can be obtained upon request. Occupational Foot Protection According to This final rule revised the PPE sections of OSHAs general industry, shipyard employment, longshoring, and marine terminals standards regarding requirements for eye and face protective devices and head and foot protection.

  2N6287 DATASHEET PDF

OSHA & ASTM Protective Footwear Requirements

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The electrical resistance must range between zero andohms. The purpose of metatarsal footwear is to prevent or reduce the severity of injury to the metatarsal and toe areas.

All footwear manufactured to the ASTM specification asfm be marked with the specific portion of the standard with which it complies. This line identifies the applicable gender [M Male or F Female ] for which the footwear is intended. It allows employers to use PPE constructed in accordance with any of three national consensus standards the two most recent and the incorporated reference in the current standards.

This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to protect against a variety of workplace hazards.

The footwear must facilitate electrical conductivity and the transfer of static electricity build up from the body to the ground. The final rule went into effect in October that year and revised the PPE sections of OSHAs general industry, shipyard employment, longshoring, and marine f22413 standards regarding requirements for eye- and face-protective devices, head protection and foot protection.

Then the requirements of additional sections such as metatarsal protection, conductive protection, electric shock protection, static dissipative protection and protection against punctures can be met. Asrm paradox exists because OSHA states in Devices constructed of metal must pass the corrosion resistance testing and show ast sign of corrosion after being exposed to a five percent salt solution for hours.

It is not the intention of this specification to serve as a detailed manufacturing or purchasing specification. Notify me of new comments via email.